So I just bought a s4 f or whatever internal ELRS with the 6 buttons missing. Can’t get firmware to update hold trim buttons in and boot into dfu mode, but it won’t see the radio through serial to update. Regardless do you have some like setup documentation for setup if as if it were a fresh radio? This is my 4th radio setup and 10 years of fpv flying and I’m finally defeated….😞
is it possible to connect jumper t lite v2 controller to iphone using cable or bluetooth connection?
the jumper t lite connected well to pc
and can be used as HID controller.
but when i trying to connect to iphone
its not working
I have purchased Jumperrc T15 recently but I don`t know how to connect it to my drone.
I have the BetaFPV Pavo Pico Brushless Whoop Quadcopter – DJI O3 VTX / ExpressLRS 2.4G.
Can you provide me with a tutorial video or a manual to follow? I`m a beginner and I can use all the help I can get.
Good afternoon. I have Jumper t-lite 2. I can’t connect BETAFPV ELRS915 Micro TX Module to it. ELRS ver 3.5.1. Script elrs2.lua is “loading.” TX module in turn on but after a while turns on wifi. It seems that there is no signal on the CRSF serial port. Can you help me?
When I turn on my remote control it just shows a no SD card on screen and won’t let me do anything else my SD card OK how can I get to work? I have Jumper t-pro v2
I have a Jumper T15 Radio that I bought 3 months ago. It was working fine until today.
The radio does not power on / turn on. When connected via USB it shows the 6 middle buttons red (I checked the batteries and they are charged) and the SYS and TELE buttons white, after a few seconds the SYS and TELE buttons start flashing white.
Only thing I was able to do was boot into DFU mode, but that didn’t solve anything.
Any solutions for this problem or should I start a refund / warranty claim with the store I bought it at?
Hello good, I bought a JUMPER T20 GEMINI and trying to update it it is impossible for me to activate the ELRS protocol Please help me put the original factory status Thank you.
16 Comments. Leave new
My USB won’t connect my computer, tried different devices and good cables
USB will charge and show when plugged in… any suggestions
excuse me For product technical support and after-sales service, please contact us at support@jumper-rc.com
So I just bought a s4 f or whatever internal ELRS with the 6 buttons missing. Can’t get firmware to update hold trim buttons in and boot into dfu mode, but it won’t see the radio through serial to update. Regardless do you have some like setup documentation for setup if as if it were a fresh radio? This is my 4th radio setup and 10 years of fpv flying and I’m finally defeated….😞
excuse me For product technical support and after-sales service, please contact us at support@jumper-rc.com
is it possible to connect jumper t lite v2 controller to iphone using cable or bluetooth connection?
the jumper t lite connected well to pc
and can be used as HID controller.
but when i trying to connect to iphone
its not working
For product technical support and after-sales service, please contact us at support@jumper-rc.com
I have purchased Jumperrc T15 recently but I don`t know how to connect it to my drone.
I have the BetaFPV Pavo Pico Brushless Whoop Quadcopter – DJI O3 VTX / ExpressLRS 2.4G.
Can you provide me with a tutorial video or a manual to follow? I`m a beginner and I can use all the help I can get.
For product technical support and after-sales service, please contact us at support@jumper-rc.com
Good afternoon. I have Jumper t-lite 2. I can’t connect BETAFPV ELRS915 Micro TX Module to it. ELRS ver 3.5.1. Script elrs2.lua is “loading.” TX module in turn on but after a while turns on wifi. It seems that there is no signal on the CRSF serial port. Can you help me?
For product technical support and after-sales service, please contact us at support@jumper-rc.com
When I turn on my remote control it just shows a no SD card on screen and won’t let me do anything else my SD card OK how can I get to work? I have Jumper t-pro v2
For product technical support and after-sales service, please contact us at support@jumper-rc.com
Good morning,
I have a Jumper T15 Radio that I bought 3 months ago. It was working fine until today.
The radio does not power on / turn on. When connected via USB it shows the 6 middle buttons red (I checked the batteries and they are charged) and the SYS and TELE buttons white, after a few seconds the SYS and TELE buttons start flashing white.
Only thing I was able to do was boot into DFU mode, but that didn’t solve anything.
Any solutions for this problem or should I start a refund / warranty claim with the store I bought it at?
Best Regards
For product technical support and after-sales service, please contact us at support@jumper-rc.com
Hello good, I bought a JUMPER T20 GEMINI and trying to update it it is impossible for me to activate the ELRS protocol Please help me put the original factory status Thank you.
For product technical support and after-sales service, please contact us at support@jumper-rc.com